Greenhouse lined inside with horticultural bubble wrap for winter, with geraniums on the staging and frost on the garden outside

How to Insulate a Greenhouse for Winter: UK Guide

The quickest way to keep a greenhouse warmer in winter is to stop the heat escaping. Sealing draughts and lining the glass with horticultural bubble wrap keeps tender plants safer on frosty nights and means any heater runs for less time. This guide explains how to insulate a greenhouse step by step, which materials are worth using and where the limits are.

How to insulate a greenhouse: the short answer

To insulate a greenhouse, first repair broken panes and seal gaps around doors, vents and glazing, then fix UV-stabilised horticultural bubble wrap to the inside of the frame, leaving vents free to open. Insulating the floor and the base, grouping tender plants in a screened-off section and storing daytime heat add further savings. On cold nights, a heater controlled by a thermostat does the rest.

In this guide you will find:

  1. Why insulate a greenhouse at all?
  2. Should I insulate my greenhouse?
  3. Insulation methods compared
  4. How to insulate a greenhouse with bubble wrap
  5. Seals, draughts and the greenhouse door
  6. How to insulate a greenhouse floor
  7. How to insulate a polycarbonate, plastic or small greenhouse
  8. Insulating without condensation: ventilation
  9. Storing heat: water, screens and fleece
  10. Combining insulation with a heater and thermostat
  11. Choosing the right level of insulation
  12. Limits and common mistakes
  13. Greenhouse insulation checklist
  14. BioGreen heaters and frost protection
  15. FAQ: insulating a greenhouse

How to insulate a greenhouse for winter: where the heat goes

A single layer of glass holds very little heat. On a clear, still winter night, the temperature inside an unheated greenhouse can fall almost as low as outside. According to the RHS, most heat is lost through draughts and through the structure itself, so good insulation tackles both: it closes the gaps that let warm air out and adds a layer of still air that slows heat loss through the glazing. The order matters, because bubble wrap over a leaking door achieves little.

Why insulate a greenhouse at all?

Insulation does not produce heat. It holds on to the warmth that the sun provides during the day and that a heater supplies at night. The benefits are practical:

  • Fewer frost spikes: temperatures fall more slowly after sunset, which gives tender plants a better chance on borderline nights.
  • Lower heating costs: a heater with a thermostat switches on later and runs for shorter periods.
  • Less wind chill: draughts are a major cause of cold spots near doors and vents.
  • A smaller heater may be enough: how much output a greenhouse needs depends on its size, the glazing and how well it is insulated. Our greenhouse heater calculator helps you estimate it.

Should I insulate my greenhouse?

Insulate your greenhouse if you keep tender plants that must not freeze or if you heat it in winter; if it holds only hardy crops, it is often better to leave the glass clear. The reason is light. The RHS notes that a layer of bubble wrap cuts out around ten percent of the light. For overwintering pelargoniums, citrus, fuchsias or dahlia tubers, which need little light but must stay frost-free, that is a worthwhile trade. Winter salads and alpines, on the other hand, need every bit of light and can suffer under a full lining.

Info

A good compromise for mixed greenhouses: line the north-facing side and the ends, where light loss matters least, and leave the sunniest roof panels clear. You keep most of the light and still reduce heat loss.

Insulation methods compared

These are the most common ways to insulate a greenhouse, with their pros and cons:

  1. Horticultural bubble wrap: Clear, UV-stabilised bubble polythene made for greenhouses, fixed to the inside of the frame. Pros: inexpensive, reusable for several seasons, easy to remove in spring. Cons: costs some light and can increase condensation.
  2. Twin-wall or multiwall polycarbonate: Panels with air channels between two or more layers, used as glazing or as inner panels. Pros: permanent and robust, insulates far better than single glass. Cons: higher cost, slightly reduced clarity, and fitting it means changing the glazing.
  3. Draught sealing: New rubber seals, clear silicone on cracks and replaced broken panes. Pros: cheap and effective, with no light loss. Cons: it does not insulate the glass itself.
  4. Floor and base insulation: Polystyrene sheets under staging and pots, insulation boards along the base, straw or mulch on borders. Pros: reduces cold from the ground and keeps roots warmer. Cons: needs space and must stay dry.
  5. Fleece and internal screens: Horticultural fleece over plants on cold nights, or a bubble wrap partition around a smaller area. Pros: flexible and targeted. Cons: needs to be put in place and removed as the weather changes.

Greenhouse insulation works best as a combination: seal first, line the glazing second, then add floor insulation and screens where your plants need them.

How to insulate a greenhouse with bubble wrap

Bubble wrap is the classic way to insulate a greenhouse in the UK. Use horticultural bubble polythene rather than packaging material: it is UV-stabilised, and the larger bubbles common on greenhouse grades let in more light than small packaging bubbles. Fit it in autumn, before the first hard frost.

  1. Clean the glass inside first, so you do not trap dirt and algae behind the lining.
  2. Measure the sides, ends and roof, and cut the wrap into panels slightly larger than each section.
  3. Fix the wrap to the inside of the frame. In aluminium greenhouses, special clips slide into the glazing bars; in wooden greenhouses, drawing pins or small tacks work well.
  4. Pull each sheet taut and overlap the joins a little, so there are as few gaps as possible.
  5. Cut the wrap around roof vents, louvres and the door so that they can still open.
  6. In spring, take the wrap down, let it dry, roll it up and store it for next winter.

Whether the bubbles should face the glass or the plants is a common question. Both work; what matters more is that the sheet sits close to the glazing with a thin, still layer of air between them and that the joins are tight.

Tip

Mark each cut panel with its position, for example "north side, panel 3", using a waterproof pen. Next autumn, the lining goes back up in a fraction of the time.

Seals, draughts and the greenhouse door

Gloved hands fitting a new rubber draught seal to a sliding greenhouse door next to a cracked pane and a tube of clear silicone sealant

Before adding any lining, walk round the greenhouse on a windy day and feel for draughts. The RHS recommends replacing broken panes, making sure vents and doors fit snugly and sealing cracks with transparent silicone, whose flexibility stops panes from breaking when the structure moves in the wind.

  • Greenhouse door: sliding doors often have gaps at the top and bottom runners. Renew worn brush or rubber seals, and hang a strip of bubble wrap or clear plastic inside the door to stop the worst draughts.
  • Roof and vents: check that vents close fully. Replace perished rubber glazing strips, and fill gaps where panes have slipped.
  • Glazing: replace cracked or missing panes; a temporary sheet of clear plastic taped over a hole is better than nothing.
  • Base: close the gap between frame and base wall with sealant or foam strips.

How to insulate a greenhouse floor

To insulate a greenhouse floor, lay polystyrene or other rigid insulation sheets under pots and staging, line the base walls with insulation boards and mulch any soil borders. Cold rises from bare ground and concrete, and roots of plants in pots are particularly exposed.

Insulated greenhouse floor with polystyrene sheets and straw, dark water butts as a heat store and a bubble wrap screen around tender citrus and geraniums
  • Stand pots on polystyrene sheets or slatted staging rather than directly on concrete or paving.
  • Fit insulation boards or bubble wrap around the inside of a low base wall.
  • Cover soil borders with a layer of straw or other dry mulch if they are not in use.
  • Keep the floor dry where you can, because wet surfaces lose heat faster and raise humidity.

How to insulate a polycarbonate, plastic or small greenhouse

The principles are the same for every greenhouse, but the details differ:

  • Glass greenhouse (aluminium): bubble wrap fixed with glazing-bar clips is the standard solution. Check rubber glazing strips and the door runners carefully.
  • Wooden greenhouse: attach the wrap with drawing pins or tacks, and check that the wood is sound and dry. Gaps often appear where timber has shrunk.
  • Polycarbonate greenhouse: twin-wall polycarbonate already insulates better than single glass. Seal the panel edges and joins, and add bubble wrap only if you heat the greenhouse or keep very tender plants.
  • Plastic, portable or pop-up greenhouse: these lightweight structures lose heat quickly and offer only limited frost protection. Secure them well against wind, add an inner layer of fleece on cold nights and move the most tender plants somewhere frost-free.
  • Small or mini greenhouse: a bubble wrap lining helps, but the small volume cools quickly. A layer of fleece over the plants or a small frost guard can make the difference on frosty nights.

Insulating without condensation: ventilation

The more airtight a greenhouse becomes, the more moisture it holds. Damp, still air encourages grey mould (botrytis) and rots, which the RHS describes as very damaging in winter. Good insulation therefore always goes together with good ventilation.

  • Open the door or a vent on mild, sunny days to let damp air out.
  • Water sparingly and in the morning, so leaves and compost surfaces dry before nightfall.
  • Leave space between plants so that air can move around them.
  • Remove dead leaves and fallen material regularly.
  • Use a fan to keep the air moving on still, damp days. Some greenhouse heaters have a fan-only mode for exactly this.

Storing heat: water, screens and fleece

Insulation works even better when the greenhouse can store some of the day's warmth. Large containers of water, such as dark water butts, warm up slowly in the sun and release heat slowly at night; the effect is modest, but it softens temperature drops. A second measure suggested by the RHS is even more effective in a large greenhouse: group your tender plants at one end and build a screen of bubble wrap and battens, so you only need to keep a smaller area frost-free. On very cold nights, a layer of horticultural fleece over the plants adds extra protection.

Info

If you overwinter tubers or bulbs, as described in our guide to overwintering dahlias, store them in the screened-off, insulated section of the greenhouse or in a frost-free shed, and check them regularly for rot.

Combining insulation with a heater and thermostat

BioGreen PALMA electric greenhouse heater on the gravel floor of a bubble-wrapped greenhouse in winter with geraniums and a lemon tree

Insulation and heating work as a team. Insulation reduces the amount of heat needed; a thermostat makes sure the heater runs only when the temperature actually drops below your setting. For tender plants, the aim is usually to keep the greenhouse frost-free rather than warm.

An electric fan heater such as the PALMA heater with THERMO 2 digital thermostat combines a 2000 W heater with a digital thermostat, and its fan-only mode helps move damp air. For larger greenhouses, the PHOENIX greenhouse heater has three output levels (1.0, 1.8 or 2.8 kW), a thermostat range of 0 to 26 °C and a fan that can run on its own. A separate THERMO 2 digital thermostat can switch devices up to a total of 3000 W and also start the air circulation of an electric heater to help against condensation. For a small greenhouse or cold frame without power, the terracotta FireFly frost guard uses a frost-protection candle to give radiant heat on frosty nights. Electric heaters in a greenhouse should only be run from a weatherproof supply protected by an RCD; if in doubt, ask a qualified electrician. Our guide to heating a greenhouse covers sizing and heater types in more detail.

Choosing the right level of insulation

  • Hardy crops only: seal draughts but keep the glazing clear for maximum light.
  • A few tender plants: group them at one end, screen that area with bubble wrap and use fleece or a small frost guard on very cold nights.
  • Frost-free greenhouse: seal, line with bubble wrap, insulate the floor and use a heater with a thermostat.
  • Mixed use: line the north side and ends, leave the sunniest roof panels clear and keep salads in the brightest spot. Our guide on what to grow in a greenhouse in winter helps you plan the crops.

Limits and common mistakes

  • Lining before sealing: bubble wrap over gaps and broken panes achieves very little.
  • Covering the vents: taping vents shut until spring traps moisture and invites grey mould.
  • Using packaging bubble wrap: it is not UV-stabilised, becomes brittle and usually lets in less light.
  • Insulating plants that need light: winter salads and alpines grow better under clear glass.
  • Expecting insulation to replace heating: in a prolonged hard frost, an unheated greenhouse can still freeze, insulated or not.
  • Leaving the lining up too long: in spring, bubble wrap holds humidity and shade, so take it down when the weather warms.

Greenhouse insulation checklist

  • Clean the glass inside and out
  • Replace broken panes and seal cracks with clear silicone
  • Renew seals on the door and vents
  • Line the glazing with UV-stabilised horticultural bubble wrap
  • Keep every vent able to open
  • Insulate the floor and the base
  • Group tender plants and screen off a smaller area if possible
  • Keep fleece ready for very cold nights
  • Use a thermometer and a heater with thermostat for frost-free conditions
  • Ventilate on mild days and water sparingly

BioGreen heaters and frost protection

These BioGreen products work together with good insulation to keep a greenhouse frost-free:

Greenhouse Heater & Fan PALMA, 2000 W, Manual Thermostat

Greenhouse Heater & Fan PALMA, 2000 W, Manual Thermostat

2000 W heater with adjustable thermostat and fan-only mode.

£149.99

View product
Electric Greenhouse Heater TROPIC, 2000 W

Electric Greenhouse Heater TROPIC, 2000 W

Stainless steel 2000 W heater, splash-proof to IPX4.

£99.99

View product
Greenhouse Heater & Fan PHOENIX, 2800 W

Greenhouse Heater & Fan PHOENIX, 2800 W

Three output levels, thermostat 0 to 26 °C, floor or ceiling mounting.

£299.99

View product
Digital Thermostat THERMO 2, -50 to +99 °C

Digital Thermostat THERMO 2, -50 to +99 °C

Plug-in thermostat for heaters and fans up to 3000 W.

£89.99

View product
Frost Guard FireFly for Candles

Frost Guard FireFly for Candles

Terracotta candle frost guard for small greenhouses and cold frames.

£29.99

View product

FAQ: insulating a greenhouse

Short answers to frequent questions about greenhouse insulation:

Does bubble wrap keep frost out of a greenhouse?

Bubble wrap slows heat loss and can keep the inside a little warmer on frosty nights, but on its own it does not make a greenhouse frost-proof. In a hard or prolonged frost, tender plants also need a heater, a frost guard or fleece.

Which way round should bubble wrap go in a greenhouse?

Either way works. More important is that the sheet is fixed close to the glass, pulled taut and overlapped at the joins, so that a still layer of air is trapped between wrap and glazing.

Does greenhouse bubble wrap need to be removed in summer?

Yes. Take it down in spring once nights are milder, because the lining reduces light and holds humidity. Dried and rolled up, horticultural bubble wrap can be reused for several winters.

What is the best way to insulate a greenhouse?

The best results come from a combination: seal draughts first, then line the glazing with horticultural bubble wrap, insulate the floor and group tender plants in a screened area. A thermostat-controlled heater covers the coldest nights.

Knowing how to insulate a greenhouse saves energy and protects your plants: seal the gaps, line the glass where the light loss is acceptable, keep the air moving and let a thermostat-controlled heater handle the hardest frosts. With these steps, your greenhouse stays frost-free through the winter at a fraction of the heating effort.

Explore greenhouse heaters